bgm - Item number: 7674257 Availability: In stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,10 kg Category: Workshop requirements> Hose clamps Other customers who are interested in hose clamps (10 pieces) -UNIVERSAL- 25-40mm - Are interested in bandwidth = 9mm, also looked for: hose clamp 10

Cracked! A pull rope can digest incredibly large loads. The tear limit of the trains we offer is several tons of pulling force. In a pinch you can even tow cars with it. Why a train breaks anyway depends on the fact that it is loaded incorrectly. Zugkiller No. 1 is the so-called common cast ridge. The brake-clutch levers are often [...]

When choosing crankshaft bearings, you should always pay attention to high quality. We have put together BGM ORIGINAL bearing sets for you here. In addition to quality bearings, the kit also includes high-quality shaft seals. Each part of the bearing set is at least at the original manufacturer level. Shaft seals in this set are only supplied by Corteco. bgm - Article number: BGM1109 [...]

Noble turn signals with LED technology. Beautify every Vespa ZIP 2 / ZIP SP from 2006 onwards in next to no time! Can be easily exchanged. Note: In some vehicles, the turn signals can no longer cycle as usual due to the low load caused by the LED technology. Load resistors (see accessories) can also be installed here. This simply between the two [...]

bgm - Item number: BGM66060P2 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Workshop requirements> Electronics Other customers who are interested in connector set for cable harness -BGM PRO- Type series 060 AM SpecialSeal, 0.85-1.25mm², waterproof - 2 plug contacts are of interest, also looked for: Plug | Cable | Ignition stator | [...]

The BGM PRO inner cable for the Lambretta rear brake (series 1-3) has a cast threaded part. ADVANTAGES The rear brake cable is now one-piece, the original compression fitting is no longer necessary. The motor can be removed from the frame much faster. The brake cable remains permanently ready for use because it is no longer squeezed. Like the original adjuster, it has an anti-twist device [...]

bgm PRO fan wheel completely developed and manufactured in Germany. This is a one-piece fan wheel without rivets or screws. Technology of the 21st century with an almost original look and design. The fan wheel has been successfully tested up to 24.000 rpm and gives the highest alternator performance with the bgm V3 ignition base plate. Features: Moment of inertia 6240 kg mm² (-5%) [...]

Reinforced locking ring from BGM Pro with increased material thickness and greater pre-tensioning force. This has holes so that it can be easily used with circlip pliers. The BGM Pro retaining rings are an ideal addition to all clutch baskets, especially if they are equipped with strong springs. All BGM Superstrong couplings from 2017 contain this ring type in series. bgm [...]

Plastic storage dummy. This allows the crankshaft to be mounted and moved in the engine housing on a trial basis and without any effort. Thus, for pure measurement purposes, neither the crankshaft nor new bearings are stressed. Ideal to control the control angle of the crankshaft (rotary valve inlet) or the cylinder (exhaust angle, overcurrent angle). Made in Germany (US) bgm - Item number: BGM1206TL Availability: in stock (Please check the [...]

bgm - Item number: BGM9310Z Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,06 kg Category: Frame> Seat> Seat spigot Other customers who are interested in seat mounting plate / strike plate -BGM ORIGINAL- Vespa PK50 (V5X1T), PK50 S (V5X2T), PK80 S (V8X5T), PK125 S (VMX5T), PK50 S automatic (VA51T), PK80 S [...]

Kyajet - PWK tuning tool (click) bgm - Item number: 2599132 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Motor> Carburetor> Carburetor needles Other customers who for needle set -BGM PRO XL- suitable for Keihin / Stage6 / bgm / Koso PE20, PWK24, PWK26, PWK28, PWK30 (HKJ, HLJ, JJK, JJL, JJM, [...]

Dial gauge holder to be able to determine the exact top dead center of the piston. Very important to be able to adjust the ignition point precisely. To do this, the cylinder head is removed and our dial gauge holder is placed across the piston and fixed with the cylinder head nuts. The holder can be mounted on all engines whose stud bolt spacing (seen across the piston) has a hole punch.