Ball bearings and Wedi sets
BGM1122 Bearing set - Shaft seal set for crankshaft -BGM ORIGINAL FKM- Lambretta DL, GP
Complete kit to re-store the crank mechanism. Absolutely recommended as a replacement measure or when installing a new crankshaft. The kit contains: 6305 FAG bearings for the drive side NU2205 bearings for the generator side * Drive-side Viton shaft seal from MB Developments Inner Viton shaft seal from MB Developments for the Maghousing Outer Maghousing shaft seal 6305 Seal Four Allen screws for [...]
A wire harness is a consumable part. After many years in heat, cold, gasoline fumes, vibrations and moisture, even the best copper cable will deteriorate. Externally, mostly well camouflaged by apparently intact insulation, the so-called inner strand is already corroded and brittle. A weak light, misfires, all of that is a thing of the past with one of our new high-quality cable harnesses. In order to [...]
Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]
Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]
Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]
With this set of swing arm bearings, lateral guidance is significantly improved. Despite the improved lateral guidance, the vibrations are significantly lower than is the case with products from PM or BPB. The swing arm bearing set fits the following vehicles - Maxi-Scooter 2T: Gilera - Runner FX 125ccm Gilera - Runner FXR 180ccm Piaggio SKR (Skipper) 125ccm Piaggio SKR (Skipper) 150ccm Piaggio [...]
Cable harness BGM ORIGINAL suitable for all Vespa PX models up to year of construction 1982 Italian version without battery. With this, the indicators, the horn (so-called buzzing) and all other consumers are supplied with power directly via the AC on-board network. The ignition base plate used in these vehicles is suitable for this with only 3 cables (contact ignition models) or 5 cables (vehicles).
Ball bearings and Wedi sets
Wideframe shaft seals for the crankshaft are available in two different designs: Round cutout for wideframe engines (material thickness of the sheet metal carrier 0,5mm) Angular cutout for largeframe engines (material thickness of the sheet metal carrier 0,8mm) The version suitable for wideframe with 0,5mm is only available still in no-name quality. The shaft seals fit and there are no problems with distorted bearings. PROBLEM [...]
Bgm Pro harness, better than original. Every cable harness is professionally manufactured and has solidly pressed (crimped) cable lugs. Where appropriate, they are also provided with protective shrink tubing. Loose wire ends are tinned, with the exception of the cable branch that leads to the light switch with screw clamps. For the greatest possible freedom of assembly, the cables are a little longer than required. Here [...]
Bgm Pro harness, better than original. Every cable harness is professionally manufactured and has solidly pressed (crimped) cable lugs. Where appropriate, they are also provided with protective shrink tubing. Loose wire ends are tinned, with the exception of the cable branch that leads to the light switch with screw clamps. For the greatest possible freedom of assembly, the cables are a little longer than required. Here [...]
BGM 50ccm replacement cylinder. Replacement for all water-cooled Peugeot Jet Force from 2013 and Speedfight 3 and Speedfight 4 scooters. The BGM cylinder is delivered in a kit with piston, piston rings and sealing kit. The original cylinder head from the Peugeot Speedfight 3 & 4 LC and Jetforce C-Tech can still be used. Replaces the Peugeot OEM number T 777327 [...]
High quality cast aluminum cylinder with a very resistant Nikasil coating. Aluminum is thermally superior to conventional gray cast iron because it emits the heat generated by the combustion process in the cylinder much better. It is not for nothing that all high-end cylinders are made of this material. A material that withstands such extreme loads as occur in the high-end sector, [...]
