Set screw BGM PRO Vespa Largeframe for fastening carburetor SI20 / SI24 / SI26 New type of screw from BGM PRO with practical hexagon head Replaces the conventional hexagon socket screw for fastening the carburetor of Vespa PX models from 1984 (PX Lusso, My, 2011, Cosa) Also fits for fastening a Malossi / Polini / Pinasco rotary valve intake manifold Can also be used as a replacement for the stud bolts / nuts for fastening the carburetor of the earlier Vespa Largeframe [...]

The BGM Pro exhaust manifold is made of stainless steel and therefore rust-free forever. It replaces the original Piaggio manifold 1: 1 and is characterized by its good fit (made in Europe). A connection for the lambda probe is available as with the original. If necessary, insert this on the thread with a little copper paste. ORGINAL AND SPORTS EXHAUST The manifold is [...]

bgm - Item number: BGM1770BS08 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,05 kg Category: Engine> Cylinder> Spacer Other customers who are looking for Spacer cylinder base -BGM PRO 177/187 ccm - Vespa PX125, PX150, Cosa125, Cosa150, GTR125, TS125, Sprint Veloce (VLB1T 0150001-) - 0,8mm interested, searched [...]

BGM gear shoulder rings are manufactured with high precision. They are hardened and ground plane-parallel to the hundredth of a millimeter. They therefore correspond exactly to the specified dimensions. The quality assurance guarantees a maximum deviation of only four hundredths of a millimeter undersize. This makes the BGM discs much more precise than Piaggio shoulder rings. WHY shoulder rings are used to compensate for the axial play between [...]

High quality new edition of the cable box for the classic Vespa PX models built up to 1984 and the Sprint Veloce models, both with battery. Not available from Piaggio for a long time, we had them reproduced in a very good quality. High quality plastic, exactly 1: 1 like the original. NOTE: Also available for PX models up to 1984 without [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

bgm - Item number: BGM2220HS12 Availability: out of stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,05 kg Category: Engine> Cylinder> Spacer Other customers who are interested in Spacer cylinder head -BGM PRO RaceTour Ø = 65,0mm 8-way screw connection - Lambretta LI 125-150, LIS, SX 125-150, TV 175 (series 2-3), DL / GP 125-150 - [...]

Inexpensive and high-quality solution from BGM to renovate an old ignition base plate. Pre-assembled cable whips are supplied to re-solder them to an existing alternator instead of the old defective cable. The cables have professionally crimped cable plugs with shrink tubing insulation as well as stripped and pre-tinned ends for attachment to the base plate. The right bougier tube for cable protection [...]

BGM clutch pinions are bulletproof. Developed for the enormous power and torque of today's engines, they are made from high-alloy steel (SCM415 / 15 CrMo 5) according to the highest manufacturing standards. The extremely high strength of the base material (up to 1100N / mm2, HRC 58-62) provides a reassuringly secure basis for the production of BGM pinions. The production meets the high [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]