bgm - Item number: BGM6610BL Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 1,66 kg Category: Motor> Rubber parts> Hoses Other customers who are interested in radiator hose set -BGM PRO silicone 180 ° C- Vespa GT 125-200, Vespa GTL 125-200, Vespa GTS 125-300, Vespa GTV 125-250 - blue are interested, also looked for: [...]

bgm - Item number: BGM66060P1 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Workshop requirements> Electronics Other customers who are interested in connector set for cable harness -BGM PRO- type series 060 AM SpecialSeal, 0.85-1.25mm², waterproof - 1 plug contact are of interest, also looked for: Plug | Cable | Ignition stator | [...]

Tool for crankshaft assembly Vespa Largeframe -BGM PRO- Made in Germany Assemble the crankshaft quickly and easily like a professional. This is possible with the quality tool from BGM PRO. With this set, the crankshaft can be drawn into its press fit in the bearing of the engine housing in a professional and material-friendly manner. Push the crankshaft as far as possible into the bearing seat (with [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

The bgm PRO pole wheel nuts are available for dL / GP or Li / TV / SX pole wheels. These differ in the outer diameter of the nuts. The Li / TV / SX also fits the dl / GP pole wheels, but has a smaller contact surface. The BGM pole wheel nuts have. Thanks to the 42CrMo4 material used, the nut is able to withstand the required tightening torque of 75 Nm despite the fine thread and [...]

Washer on crankshaft under clutch from bgm Pro The washer between crankshaft and clutch has three very important tasks to fulfill: Establishing the controlled preload between crankshaft and ball bearing Providing a plain bearing surface for the clutch pinion during operation of the clutch The correct distance between the clutch and the Manufacture bearings so that the gearing with [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

The Kickstarter KLAPPBAR are long-running favorites because of their super sporty look. The very high quality aluminum alloy, the best workmanship and optimal fit characterize the kickers in technical terms. Visually, the Burner Moto GP gives a pure feeling, the wide contact surface ensures quick starts! The kickstarter can be assembled in a few simple steps, an easy exercise even for inexperienced screwdrivers. [...]

BGM PRO Superstrong clutch linings type CR Suitable for retrofitting all clutches of the COSA2 type (exception: BGM Superstrong CR) for Vespa Largeframe (PX / Cosa / T5, Rally etc.) This CR lining set contains: 3x clutch disks with two sides, 1x clutch disc with one side it is suitable for all Vespa largeframe clutches of type COSA2 (exception: BGM Superstrong CR) [...]

Cylinder base gasket -BGM PRO- 1,5mm Pinasco 213ccm bgm - item number: 3820043 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Engine> Cylinder> Spacer Other customers who Interested in spacer cylinder base -BGM ORIGINAL Pinasco 213 ccm / Piaggio 200 ccm- Vespa PX200, Rally200 - 1.5mm, also searched [...]

bgm - Item number: BGM1550H Availability: out of stock (Please check availability here in the Scooter Center Shop) Weight: approx. 1,31 kg Category: Engine> Cylinders> Cylinder heads Other customers who are interested in cylinder head -BGM PRO 150 ccm, wideframe , Faro Basso, Ø = 57mm, stroke = 57mm- Vespa 1953-1959, VM, VN, ACMA, VB1T, VGL1T, VL1T are also looking for: [...]

Set of engine oil dipstick and gear oil dipstick BGM PRO made of CNC milled, high-strength aluminum. Available in silver or black anodized Suitable for all Piaggio Leader / Quasar 125-300ccm engines 1: 1 replacement for the original plastic dipstick No tools required High-quality manufacture (dipstick with thread + high-strength screw adhesive secured in the head) Incl. O-ring Ready for direct installation ENGINE OIL CHECK Do not run the engine warm, if necessary [...]