Cable branch BGM PRO for mounting the voltage regulator directly on the engine block - conversion to electronic ignition Vespa Smallframe / Largeframe WHY BGM6690V50 With this cable branch the voltage regulator can be positioned more freely, regardless of the connection to the conversion wiring harness (item no .: 9077011). Vespa Smallframe With the Vespa smallframe models (V50, 50N, Special, PV etc.) it is ideally connected directly with [...]

Cylinder base gasket -BGM PRO- 1,5mm Malossi 139ccm & 166ccm bgm - item number: 3820038 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Engine> Cylinder> Spacer Other customers, who are interested in spacer cylinder base -BGM ORIGINAL Malossi 139/166 ccm- Vespa PX80, PX125, PX150 - 1.5mm, were looking for [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

BGM screw / clamp nipples are manufactured by a supplier for the Japanese motorcycle industry in excellent quality. The dimensions correspond exactly to the old originals from Piaggio / Innocenti. This guarantees a perfect fit. As in the original, the clamping screws for the shift cables have an internal plate. This protects the inner cable of the Bowden cable and helps to [...]

bgm - Item number: 4350011 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,14 kg Category: Frames> Cables> Cable pulls Other customers who are interested in universal pull-Ø = 1,2mm x 2500mm, nipple Ø = 5,5mm x 7mm- used as throttle cable - turned interested, also looked for: Zug | Universal | Throttle cable [...]

bgm - Item number: 3332368 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Workshop requirements> Electronics Other customers who are interested in cable lug - flat receptacle 90 ° angle 6,3mm Ø = 0,75-1,5mm²- 10pcs. interested, also searched for: cable lug | Electrics | Connection | Cable | Cable connector | Flat plug | Ring eyelet | [...]

The bgm Pro kick starter pinions are made of high-alloy NiCrMo case-hardened steel (20NiCrMo2-2 / AISI8620) and then case-hardened. The precisely defined surface hardening to 58-60HRC makes the pinion extremely resistant to wear. They are manufactured exactly according to Piaggio original dimensions. Always consistently high quality. No compromise. LUBRICATION GROOVE As a special feature, the bgm Pro pinions also have a lubricating groove in the [...]

Intake manifold -BGM PRO Evolution- Piaggio - CS = 23mm. Open intake manifold for all Piaggio scooters with the 50 cc engine housing. The ideal connection between the Dellorto, Gurtner and Arreche carburetors with 23 mm connection width. The carburetor stands straight back and offers a crisp, short intake path for a clean turning behavior. Better acceleration, free turning and higher [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

bgm - Item number: 7675166 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Workshop requirements> Electronics Other customers who are interested in insulating tubing for cable lug round plug-in sleeve 4mm Ø = 0,5 -1,0mm²- 10pcs. interested, also searched for: insulating tube | Bougie ear | Grommet | Cable grommet | Conduit | Conduit | Cable conduit | [...]

Lambretta cylinder head gasket with 2,5 mm thickness and 71,0 mm diameter. Ideal to compensate for connecting rod lengths, compression heights, longer strokes or twisted cylinders. bgm - Item number: BGM0247 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Engine> Cylinder> Spacer Other customers who are interested in spacer cylinder head [...]

Lambretta cylinder base gasket with a thickness of 3,0 mm for the large engine blocks with 200-250 ccm displacement. Ideal to compensate for connecting rod lengths, differences in the heights of the engine sealing surfaces, twisted cylinders or to be able to experiment with the control times. The size of the overflow channels is dimensioned so that it corresponds to the standard overflows. Ideally, this should match the engine block and cylinder.