The BGM stainless steel rim is manufactured in Germany with high precision by a renowned and, of course, certified company. The result is a rim that even Enrico Piaggio couldn't have made better. The high-strength rim is characterized by perfect concentricity, absolute freedom from rust and a reinforced rim flange. The rim is screwed into stainless steel with the special nuts provided. Their [...]

bgm - Item number: BGM4752G Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Workshop requirements> Electronics Other customers who are interested in Bougie pipe -UNIVERSAL Ø = 6mm- 5m - gray , also searched for: Bougierohr | Heat shrink tubing | Insulating tube | Electrics | Management | Wiring harness | Cable hose | Cable harness hose [...]

High quality petrol hose made for us in Italy by the manufacturer of the original Piaggio petrol hoses. Perfect for all Vespa scooter models such as Vespa PX, Sprint, Rally, VBB as well as V50, PV, ET3, PK etc. suitable. Inside diameter: Ø7mm Outside diameter: Ø14mm Length: 750mm The large outside diameter ensures a perfect seal in the rubber grommets in the frame. Additionally [...]

High-quality inner cable set as the ideal repair kit for on the go or as a replacement for the workshop. The set includes: 2x Ø = 1,9mm x 2100mm (nipple pear type, used as a clutch cable / brake cable in the front), 2x Ø = 1,6mm x 2100mm (nipple Ø = 5,5mm x 7mm, used as a shift cable) 1x Ø = 1,2 , 2500mm x 5,5mm (nipple Ø = 7mm x 1mm, used as throttle cable) 1,2x Ø = 2500mm x XNUMXmm (nipple [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

BGM clutch pinions are bulletproof. Developed for the enormous power and torque of today's engines, they are made from high-alloy steel (SCM415 / 15 CrMo 5) according to the highest manufacturing standards. The extremely high strength of the base material (up to 1100N / mm2, HRC 58-62) provides a reassuringly secure basis for the production of BGM pinions. The production meets the high [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

bgm - Item number: BGM666PK Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 6,70 kg Category: Engine> Ignition> Ignitions Other customers who are interested in ignition set -BGM PRO 12V Touring- Vespa Smallframe PK XL, PK XL2, HP3, HP4 - 1600g are also interested in: Ignition | Set | [...]

bgm - Item number: 7673423 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,03 kg Category: Frame> Electrics> Carburettor components Other customers who are interested in mixture adjustment idle gas screw set -DellOrto PHBL 22-24-25 / PHBH 28-30 carburettor interested, also looked for: Mixture adjustment | Idle screws | Set | Screw | Adjusting screw | [...]

Open intake manifold for Minarellis with upright cylinder Intake manifold with a small connection, suitable for the carburettors with a small connection width (Areche 17,5 - 21 mm, Dellorto 12 - 19 mm). Decent increase in performance, as the engine can finally breathe freely. The result is better acceleration values ​​and freer turning and thus higher top speed. bgm - Article number: A201 Availability: on [...]

Remote air filter system based on the bgm PRO suction hose and a Marchald foam air filter. bgm PRO suction hose with increased volume in front of the carburetor compared to the original suction hose. The intake hose is available with four different connection sizes on the carburetor: 40 mm (e.g. Dellorto PHBL 25), 42mm (Dellorto PHBH 28-30), 45 mm (Mikuni TM24 and Jetex SH22) or 50 mm [...]

BGM screw / clamp nipples are manufactured by a supplier for the Japanese motorcycle industry in excellent quality. The dimensions correspond exactly to the old originals from Piaggio / Innocenti. This guarantees a perfect fit. As in the original, the clamping screws for the shift cables have an internal plate. This protects the inner cable of the Bowden cable and helps to [...]