Lambretta bgm PRO MRB RaceTour piston kit with 65 mm diameter. Complete piston kit consisting of: piston, two steel piston rings a 1 mm thick, piston pin and clips. The piston is manufactured exclusively by the Meteor company. The piston is primarily intended as a replacement piston for the bgm RaceTour cylinder, but can also be used as a conversion piston.

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

bgm - Item number: BGM0291HS15 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,05 kg Category: Engine> Seals> Spacer Other customers who are interested in Spacer cylinder head -BGM ORIGINAL Ø46mm- Vespa P80X , PX80, PX80E - 1.5mm, also searched for: Spacer | Cylinder head | Distance seal | Distance | [...]

Precisely manufactured BGM Pro switch scale set for Lambretta 1/2/3 series Made of high-strength aluminum, CNC milled, silver anodized Consists of: Adjustment block Aluminum adjustment screws 3x, stainless steel switch rod Aluminum switch scale Aluminum fastening screws Perfect set for backlash-free control of the circuit. The BGM Pro shift cables (with low-friction PTFE inner coating) and a well-separating clutch (BGM [...]

Revised version of the proven Lambretta bgm PRO train set. The well-known features such as the correct length of the outer and inner sleeves, the outer cable with a PE sleeve for easy operation and the detailed plan for laying the cables have of course been retained. The many small improvements in detail are new, the end sleeves are now double pressed, the inner cables are [...]

Motor housing bolt set that contains all removable motor bolts of the motor housing. The bolts are made of high-strength steel (10.9) and are permanently protected against corrosion by a browning process. Also included are the snap rings, washers and nuts, all of which are galvanized. The set corresponds to the original dimensions used ex works and is a high-quality 1: 1 replacement for the original [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

Lambretta cylinder base gasket with a thickness of 2,5 mm for the small engine blocks with 125-193 ccm displacement. Ideal to compensate for connecting rod lengths, differences in the heights of the engine sealing surfaces, turned cylinders or to be able to experiment with the control times. The size of the overflow channels is dimensioned so that it corresponds to the standard overflows. Ideally, this should match the engine block and cylinder.

High quality electric cable with robust PVC sheath. Available in many different colors, such as those used in Piaggio vehicles. Available in cable cross-sections of 0,85mm² and 2,0mm². Outside diameter 0,85mm² = Ø2,3mm outside diameter 2,0mm² = Ø3,1mm Cable type: Single core Insulation: Special PVC according to DIN ISO 6722 and LV112 Temperature range: -40 to + 120 ° C Conductor: Bare copper wire Length: 10 meters [... ]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

To be able to mount a different handlebar on your scooter, you need a suitable holder. The brackets are designed to fit our downhill and Fehling handlebars with a 22,2mm diameter. The workmanship and fit are at a very good level and assembly is child's play. This ensures that the handlebars are always securely seated. bgm [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]