BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

The bgm PRO silent rubbers improve the driving behavior through a much more precise guidance of the motor in the frame. The reinforced rubbers have asymmetrical degrees of hardness. Therefore, the driving comfort is maintained despite the tighter suspension. With the reinforced bgm engine silent rubbers supplied in pairs, the chassis gains directional stability, steering precision and rigidity. The assembly is easy and offers eg [...]

bgm - Item number: BGM01700N Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Motor> Coupling> Nuts Other customers who are interested in M10 x1.00 (fine thread) SW = 16 half height -BGM PRO- (used as clutch nut Vespa for auxiliary shaft BGM PRO for V50, PV125, ET3, PK S, PK [...]

bgm - Item number: 3330039 Availability: out of stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,03 kg Category: Engine> Cylinder> Spacer Other customers who are interested in Spacer cylinder base -BGM PRO 166/172 / 177 cc- Vespa PX80, PX125, PX150 - 4.0mm (without cut-outs for overcurrent channels), also looked for: Spacer | [...]

Clever fuel tap wrench from BGM PRO in a cranked version. Instead of a simple open-end wrench, use a modern multi-toothed spanner like a ring spanner This makes it quicker and easier to grab and turn the nut of the fuel tap. Simple, simple, good! Suitable for all Vespa with a fuel tap nut with a wrench size of 32mm and a filling diameter greater than Ø35mm This applies to [...]

Developed for performance-oriented engine concepts. The fastening should be done with Loctite medium strength WITHOUT a locking plate. The recommended tightening torque is 55-60 Nm. Tried and tested in racing and found to be good. bgm - Item number: 7672106 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Engine> Crankshaft> Nuts Other customers, [...]

We are now offering you high-quality cable lugs in bare brass for crimping and / or soldering. The bare brass is very easy to solder and corresponds to the appearance of the original wiring harness. In connection with our suitable cables, bougie tubes and shrink tubing sets, a defective cable harness can be repaired or, if necessary, even completely new. The cable lugs are [...]

Compact voltage regulator for all alternators with 12 volts. The controller supplies alternating current and optionally also direct current. Thus, it is not only the perfect and reliable replacement for all conventional voltage regulators, it also enables a modern expansion of the existing on-board network. AC - AC alternating current: Input and output for the unregulated alternating current of the ignition base plate and the regulated current [...]

BGM PRO brake shoes with lining material 'MADE IN GERMANY' QUALITY The BGM Pro brake shoes are manufactured exclusively for BGM by one of the most renowned Italian brake lining manufacturers. The covering material comes from the German manufacturer Beral. The aluminum base is cast in the original shape, so a perfect fit is always guaranteed. MATERIAL + PERFORMANCE The pad mixture for the [...]

BGM primary gears are bulletproof. Developed for the enormous power and torque of today's engines, they are made of high-alloy steel (SCM415 / 15 CrMo 5) according to the highest manufacturing standards. The extremely high strength of the base material (up to 1100N / mm2, HRC 58-62) offers a reassuringly secure basis for the production of BGM primary wheels. The production meets the high [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

Washer on crankshaft under clutch from bgm Pro The washer between crankshaft and clutch has three very important tasks to fulfill: Establishing the controlled preload between crankshaft and ball bearing Providing a plain bearing surface for the clutch pinion during operation of the clutch The correct distance between the clutch and the Manufacture bearings so that the gearing with [...]