bgm - Item number: 708090 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Engine> Carburettor> Sockets Other customers who are interested in vacuum connection -BGM ORIGINAL- M6 (SW = 8, with O-ring, Ø inside = 3,5mm, Ø outside = 6,1mm, length = 30mm), also looked for: vacuum connection | [...]

Clever fuel tap wrench from BGM PRO in a cranked version. Instead of a simple open-end wrench, use a modern multi-toothed spanner like a ring spanner This makes it quicker and easier to grab and turn the nut of the fuel tap. Simple, simple, good! Suitable for all Vespa with a fuel tap nut with a wrench size of 32mm and a filling diameter greater than Ø35mm This applies to [...]

bgm - Item number: 7674257 Availability: In stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,10 kg Category: Workshop requirements> Hose clamps Other customers who are interested in hose clamps (10 pieces) -UNIVERSAL- 25-40mm - Are interested in bandwidth = 9mm, also looked for: hose clamp 10

BGM gear shoulder rings are manufactured with high precision. They are hardened and ground plane-parallel to the hundredth of a millimeter. They therefore correspond exactly to the specified dimensions. The quality assurance guarantees a maximum deviation of only four hundredths of a millimeter undersize. This makes the BGM discs much more precise than Piaggio shoulder rings. WHY shoulder rings are used to compensate for the axial play between [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

Complete locking set for the auxiliary shaft of Vespa largeframe engines such as PX, T5, Cosa, Rally Contains 1x washer 1x locking washer 1x nut M9 / SW17 Tightening torque of auxiliary shaft nut: 30-35Nm The reinforced BGM primary repair set (BGM0195F48) and the auxiliary shaft set ( BGM6503PKT) bgm - item number: BGM6503NKT Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: [...]

The PickUp, like a Hall sensor in a car, is responsible for the correct ignition timing. It gives the CDI the signal when it should trigger the ignition signal. Inside the PickUp there is a coil with very fine copper wire windings. This induces a voltage during the rotation of the magnetic pole wheel. As soon as the area of ​​the so-called [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

Cylinder head gasket -BGM PRO- 2.0mm Polini 177ccm, DR 177ccm bgm - item number: 3820054 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx who are for Spacer cylinder head -BGM ORIGINAL Polini / DR / Parmakit 0,02 cc- Vespa PX177, PX125, Cosa150, [...]

BGM adjusting screws are manufactured in an excellent quality by a supplier for the Japanese motorcycle industry. The dimensions correspond exactly to the old originals from Piaggio. This guarantees a perfect fit. As in the original, the adjusting screws have an extra high lock nut. The size M7x25mm is suitable for use as an adjusting screw for the rear brake cable on the engine.

BGM screw / clamp nipples are manufactured by a supplier for the Japanese motorcycle industry in excellent quality. The dimensions correspond exactly to the old originals from Piaggio / Innocenti. This guarantees a perfect fit. As in the original, the clamping screws for the shift cables have an internal plate. This protects the inner cable of the Bowden cable and helps to [...]

High-quality CNC sports levers from bgm PRO for vehicles with cable brakes at the front. Suitable for Vespa Largeframe models built in 1957-1998: PX, T5, Sprint, Rally, GT, GTR, TS, VNA, VNB, VBB, VBA, GS, SS180 Smallframe built in 1963-1989: V50, 50N, V90, PV125, ET3 , PK S *, PK XL1 * Milled from solid aluminum, with an elegant, resistant, hard-anodized surface. Ergonomically clear [...]