BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

BGM PRO Superstrong clutch linings type CR Suitable for retrofitting all clutches of the COSA2 type (exception: BGM Superstrong CR) for Vespa Largeframe (PX / Cosa / T5, Rally etc.) This CR lining set contains: 3x clutch disks with two sides, 1x clutch disc with one side it is suitable for all Vespa largeframe clutches of type COSA2 (exception: BGM Superstrong CR) [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

Precisely manufactured shift pin for all largeframe transmissions from approx. Year of construction 1984 - Vespa PX, T5, Cosa, Motovespa TX. Always used with a flat type switch cross. If a non-flat switch cross is installed in your engine and a washer is also installed between the switch bolt and the switch cross, the bolt shown here cannot be used. You have [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

BGM PRO speedometer cables correspond to the factory specification and impress with their high quality and low price. All speedometer cables have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as a high-quality outer shell or a properly pressed square. The installation of the already greased speedometer cable is easy.

If a crankshaft with a longer stroke is used, this additional stroke has to be compensated for for two reasons. On the one hand due to the mechanical conditions to prevent the piston from hitting or the engine runs too highly compressed, on the other hand to keep the control angle of the cylinder, which determines the performance, within a reasonable range. If the stroke is extended, [...]

Spacer -BGM PRO- Vespa V50, PV 125, ET3, PK 50-125 - 8 mm. Spacer to compensate for the longer connecting rod of the 54 mm long stroke shaft. bgm - Item number: BGM0223 Availability: not in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,08 kg Category: Motor> Cylinder> Spacer Other customers who are [...]

BGM ignition base plates and ignition kits are the solid basis for a high-quality engine. The powerful alternator guarantees perfect light output, the HQ ignition components a clean and powerful engine, the BGM pole wheel an extremely quiet engine run. Ideal for upgrading a decrepit, contact-controlled electrical system to a modern, maintenance-free high-performance ignition. ADVANTAGES: High light output thanks to maximum number of windings Proven excitation coil [...]

bgm - Item number: SC5012 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Engine> Rubber parts> Rubber parts Other customers who are interested in rubber hose for cable ignition base plate -BGM ORIGINAL- Vespa PK interested, also looked for: rubber hose | Cable | Ignition stator | Hose | Cable rubber | Ignition rubber [...]

BGM end sleeves are manufactured in excellent quality by a supplier for the Japanese motorcycle industry. The dimensions correspond exactly to the old original from Piaggio. This guarantees a perfect fit. End sleeves have a thin shoulder at the end. They are required to fix outer cable shells in the sheet metal of the abutment (in the steering head) to prevent slipping and

The right tool for perfectionists when adjusting the carburetor. With this useful tool, the actual nozzle size can be determined in no time at all. bgm - Item number: 1800026 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Workshop requirements> Tools Other customers who are interested in nozzle measuring gauge -UNIVERSAL- Ø = 0,45-1,50 , XNUMXmm are interested, searched [...]