The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

bgm - Item number: BGM6010S20 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Engine> Gearbox> Shims Other customers who are looking for gear shims -BGM ORIGINAL- Lambretta Series 1-3 - 2,00mm are interested, also looked for: Gear shim | Thrust washer | Washer gear | Gear disc | Spacer [...]

The tires are indisputably one of the most important components of our scooters. It establishes contact with the road and is therefore not only responsible for safety but also to a large extent for driving pleasure. The goal was to develop a tire with which you can iron through curves and roundabouts in wet conditions as well as in dry conditions [...]

Replacement piston for the BGM PRO150ccm cylinder for Vespa Wideframe. Here in the standard size, suitable for the cylinder as it is delivered (no oversize). bgm - Item number: BGM1550PB Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 3,20 kg Category: Engine> Cylinder> Cylinder Other customers who are [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

When choosing crankshaft bearings, you should always pay attention to high quality. We have put together BGM ORIGINAL bearing sets for you here. In addition to quality bearings, the kit also includes high-quality shaft seals. Each part of the bearing set is at least at the original manufacturer level. Shaft seals in this set are only supplied by Corteco. bgm - Article number: BGM1109 [...]

High quality new edition of the cable boxes for the classic Vespa PX. Here in a special version for the PX models not launched in Germany until 1984 WITHOUT a battery. The wiring harness of these vehicles already has a round connector on the ignition side, like the later PX Lusso models. Therefore this box is higher than that of the German [...]

Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]

The BGM Pro exhaust manifold is made of stainless steel and therefore rust-free forever. It replaces the original Piaggio manifold 1: 1 and is characterized by its good fit (made in Europe). A connection for the lambda probe is available as with the original. If necessary, insert this on the thread with a little copper paste. ORGINAL AND SPORTS EXHAUST The manifold is [...]

Carburetor revision kit -PWK- Keihin. All wear parts in one handy set to overhaul your PWK carburetor. Idle adjustment screw not suitable for original Keihin carburetors! bgm - Item number: BGM8500G Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Engine> Service> Carburetor revision kit Other customers who are interested in [...]

bgm - Item number: BGM6010S23 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Engine> Gearbox> Shims Other customers who are looking for gear shims -BGM ORIGINAL- Lambretta Series 1-3 - 2,30mm are interested, also looked for: Gear shim | Thrust washer | Washer gear | Gear disc | Spacer [...]

The right tool for perfectionists when adjusting the carburetor. With this useful tool, the actual nozzle size can be determined in no time at all. bgm - Item number: 1800026 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Workshop requirements> Tools Other customers who are interested in nozzle measuring gauge -UNIVERSAL- Ø = 0,45-1,50 , XNUMXmm are interested, searched [...]