bgm - Item number: 7676603 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Motor> Rubber parts> Bushings Other customers who are interested in bushing silent rubber shock absorber / motor -BGM ORIGINAL ( Made in Germany) Ø = 9mm x 44mm- Vespa VNA, VNB, VBA, VBB are interested, also looked for: Bush | Silent rubber [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

bgm - Item number: BGM66060P1 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Workshop requirements> Electronics Other customers who are interested in connector set for cable harness -BGM PRO- type series 060 AM SpecialSeal, 0.85-1.25mm², waterproof - 1 plug contact are of interest, also looked for: Plug | Cable | Ignition stator | [...]

bgm PRO wiring harness for all Lambrettas with electronic ignition. The wiring harness is made with as few cables as possible, so it corresponds to the ideal of minimal electronics. The wiring goes to CDI, voltage regulator, headlight connector in the steering head, brake light switch and taillight. There are no annoying clipboards. A piece of bougier tube for the cable branch of the ignition base plate is included in the scope of delivery. The wiring harness [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

High-precision BGM PRO auxiliary shaft axis for the bearing of the primary drive of the Vespa PX125-200 models. Here in a complete set including bearings, bearing needles and circlips. This means that a secondary shaft can be completely re-stored. We recommend the BGM locking set (BGM6503NKT) to secure the auxiliary shaft axis. For a comprehensive overhaul, we offer the primary repair kit from BGM (BGM0195F48). This contains reinforced [...]

We carry indicator glasses from Piaggio, Siem, Triom as well as Bosatta and BGM. TRIOM / SIEM Both high-quality manufacturers who manufacture for Piaggio and therefore have an E-mark. The two manufacturers only differ slightly in terms of design and color. For perfect color consistency and fit, read off which manufacturer it is on the indicator body before buying. PIAGGIO Piaggio will [...]

We were so dissatisfied with the quality of all silent blocks that we took on the matter. The main focus was on reducing vibrations, and we tested all possible combinations of silent blocks. Different hardnesses and different hardnesses on the left and right side. We now have good degrees of hardness for the left and right side [...]

Cylinder base gasket -BGM PRO- 1,5mm DR 177ccm, Pinasco 177ccm bgm - item number: 3820039 Availability: not in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,03 kg Category: Engine> Cylinder> Spacer Others Customers who are interested in spacer cylinder base -BGM ORIGINAL DR 177 ccm- Vespa PX80, PX125, PX150 - 1.5mm, [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

We carry indicator glasses from Piaggio, Siem, Triom as well as Bosatta and BGM. TRIOM / SIEM Both high-quality manufacturers who manufacture for Piaggio and therefore have an E-mark. The two manufacturers only differ slightly in terms of design and color. For perfect color consistency and fit, read off which manufacturer it is on the indicator body before buying. PIAGGIO Piaggio will [...]