Mixture adjustment screw without spring for bgm PWK, Keihin PWK and Stage6 PWK carburetors bgm - item number: BGM8507 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Engine> Carburetor> Carburetor components Other customers who are interested in mixture adjustment screw -BGM for PWK- (bgm, Stage 6, Keihin) were also looking for [...]

Open intake manifold for all Piaggio scooters with 2-stroke engine housing (50cc, 125cc, 180cc). The carburetor stands straight back and offers a crisp, short intake path for a clean turning behavior. Better acceleration, free turning and higher top speed! Due to the changed installation position of the carburetor, the original connection hose to the air filter box can no longer be used. With a Ø30mm connection width, [...]

Lambretta bgm PRO MRB RaceTour membrane piston kit with 65 mm diameter. Complete piston kit consisting of: piston, two steel piston rings a 1 mm thick, piston pin and clips. The piston is manufactured exclusively by the Meteor company. The piston is the perfect choice if you have converted your RT 195 cylinder to diaphragm control and have a durable [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

With the CDI holder from bgm it is possible to install a CDI for the electronic ignition on a Ciao of the first and second series without further modifications. The holder is simply placed under the two motor screws and attached to the motor. The following materials are required for assembly: 1. 4x washers M5x15x1,2mm 2. 2x self-locking nuts [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Complete set to match your indicators and the taillight perfectly to the look of the scooter. With a few, easy-to-use hand movements, you get a great look! bgm - Item number: K070180 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,16 kg Category: Frames> Electronics> Indicator glasses [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

bgm - Item number: BGM0194S Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Engine> Gearbox> Primary repair Other customers who are looking for springs for primary repair kit -BGM PRO reinforced- Vespa Wideframe VM, VN, VL, VB, VNA, VNB, VBA, VBB, VGLA, VGLB, VNC1T (-110000) are interested, also searched [...]

bgm - Item number: BGM7707A Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Frame> Shock absorbers> Shock absorber mountings Other customers who are looking for spring plates for shock absorber springs in front, top fork / swing arm -BGM PRO- Largeframe Sprint (VLB1T), Rally (VSD / VSE), GT / GTR125 (VNL2T), Super (VNC / VBC), TS125 (VNL3T), VNA, VNB, VBA, VBB, [...]

Exhaust BGM Pro TOURING Banana for Vespa Smallframe PV125, ET3 models. Also fits 125ccm (or larger) converted Vespa V50, 50N, 50 Special, V90, SS90, 90 Racer, V100 models. The BGM Pro Banana in the TOURING version offers discreet optics and acoustics in connection with a high-torque and broadband characteristic. It offers significantly more [...]