The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Tapered roller bearings have a larger contact surface and are therefore significantly more resilient than conventional factory solutions with ball bearings. Tapered roller bearings can cope with the high loads of powerful braking systems much better and are also much more wear-resistant. They increase active driving safety by ensuring the ideal state of smooth, non-locking steering for a very long time. A criterion that [...]

Spacer plate for the HP4 ignition on Vespa PX, T5 and Cosa engines. If the tolerances of the engine housing, crankshaft, ignition base plate and fan wheel add up unfavorably, this can lead to a fluttering ignition timing. The reason for this is that the pick-ups in the fan wheel are not aligned with the pick-up. In order to compensate for this difference, we offer you this packing [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

We are now offering you high-quality cable lugs in bare brass for crimping and / or soldering. The bare brass is very easy to solder and corresponds to the appearance of the original wiring harness. In connection with our suitable cables, bougie tubes and shrink tubing sets, a defective cable harness can be repaired or, if necessary, even completely new. The cable lugs are [...]

Perfectly matching new edition of the leg shield edge protection for the Vespa PK50 S, PK80 S, PK125 S and PK125 ETS models. The PK S / PK ETS models have, compared to all other models, an inverted flanging of the leg shield edge. The PK S / ETS-specific edge protection was therefore not available for years. The edge protection is available in: Silver (PK S [...]

bgm - Item number: BGM6710W Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,40 kg Category: Frame> Electrics> Vehicle electrics Other customers who are interested in adapter cable set for horn rectifier -BGM PRO- used for BGM6710, also looked for: Horn rectifier | Horn regulator | Horn transformer | Rectifier | Diode | Diodes [...]

BGM PRO shaft sealing rings made of high-quality and ethanol-resistant (E10) FKM / Viton® * CORRECT HEIGHT (20x62x7MM INSTEAD of 20x62x6.5MM) The coupling-side BGM PRO shaft sealing ring has an overall height of 7mm instead of the 6.5mm usual with other manufacturers. The BGM PRO shaft seal is based on the original old model from Piaggio. Anyone who takes apart an old original engine will [...]

Speedometer glass incl. Decorative ring WHAT FOR Perfect repair kit for the speedometer. Either to replace a scratched / defective glass or to visually upgrade the speedometer. We also offer the sets in various designs. In our opinion, the tinted glass looks particularly elegant. HOW In the set is the speedometer glass ring that connects the speedometer glass and the speedometer [...]

Air filter fleece BGM PRO for Motovespa Largeframe models 125-160cc High quality filter fleece from Marchald (Italy), manufactured for BGM PRO. Suitable for the direct intake engines (carburetor sits directly on the cylinder) of the largeframe Motovespa engines. 1: 1 replacement for the original wire mesh. Significantly better and finer filtering with a higher air flow rate at the same time. Therefore also ideal for engines that have already been upgraded. [...]

The bgm PRO clutch steel discs are manufactured exactly flat and allow the clutch to be separated precisely. The clutch can be perfectly dosed thanks to the very good concentricity. Perfect concentricity No burrs Good controllability of the clutch Linings separate cleanly Suitable as a replacement for the original steel discs, no modifications necessary. We recommend BGM Pro Street gear oil as a lubricant [...]

We are now offering you high-quality cable lugs in bare brass for crimping and / or soldering. The bare brass is very easy to solder and corresponds to the appearance of the original wiring harness. In connection with our suitable cables, bougie tubes and shrink tubing sets, a defective cable harness can be repaired or, if necessary, even completely new. The cable lugs are [...]