Clever tool from BGM for the damage-free installation of studs. Screw the BGM Pro tool onto the stud bolt and counter with the integrated hexagon socket screw. It is braced with the thread of the stud bolt. Now turn the outer wrench flat. The stud bolt is fixed and is loosened or screwed in. Pay attention to a sufficiently firm counter-locking so that [...]

bgm - Item number: BGM2280 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,21 kg Category: Frame> Handlebars> Shift gas pipes Other customers who are interested in gas pipe -BGM ORIGINAL- Vespa PX , PK S, PK XL1 - l = 177mm Ø = 24mm, also looked for: Gas pipe | Inner tube | Gas wave | Throttle [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

All Vespa brake light switches are actuated when installed. In other words, the pedal already presses the spring-loaded actuating pin in the idle state. That is why we always name the function of the switches as they work when installed. On the other hand, if you hold the switch loosely in your hand, the circuit diagram is exactly the opposite of what we indicated. In the [...]

The BGM PRO ignition set made of high-quality components for a quick conversion of the Vespa to a maintenance-free, powerful and reliable ignition / generator unit. FEATURES Conversion from contact ignition to electronic ignition bright light already in idle voltage-stabilized 12 volt on-board network maintenance-free and reliable electronic ignition starts immediately good concentricity lighter, balanced pole wheel more power better acceleration alternator [...]

For Quattrini M210 reworked manifold for the bm PRO Big Box. This means that all Big Boxes of versions 2 to 4 can be installed on the Quattrini M210. The M210 has an angled exhaust flange on the cylinder. The angle can only be found on the M210. The TS1 outlet connection must also be reworked and adapted. The distance [...]

bgm - Item number: BGM6010S19 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Engine> Gearbox> Shims Other customers who are looking for gear shims -BGM ORIGINAL- Lambretta Series 1-3 - 1,90mm are interested, also looked for: Gear shim | Thrust washer | Washer gear | Gear disc | Spacer [...]

bgm - Item number: BGM4752G Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Workshop requirements> Electronics Other customers who are interested in Bougie pipe -UNIVERSAL Ø = 6mm- 5m - gray , also searched for: Bougierohr | Heat shrink tubing | Insulating tube | Electrics | Management | Wiring harness | Cable hose | Cable harness hose [...]

Two-part series resistor set with 10 watt resistance. This makes it possible to reduce the excessively high frequency after installing LED indicators. So LED indicators can be used without a special LED indicator relay. The set is ready-made so that it can be used in parallel in the indicator cable. The resistor is connected as if you were [...]

Normal version of the BGM Superstrong clutch spider. Can be used on all conventional auxiliary shafts. If the Superstrong is to be used on a DRT auxiliary shaft, we recommend using our special version for DRT auxiliary shafts. As a result, the coupling sits lower by the amount that the DRT auxiliary shaft is longer (1,5mm). This means that the clutch cover does not have to be placed under a compensating spacer. [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

bgm - Item number: BGM2254 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,03 kg Category: Motor> Crankshaft> Nuts Other customers who are interested in pole wheel nut M11 x 1,50 (high strength) Collar Ø = 24mm h = 3mm SW = 14 -BGM PRO- Vespa Wideframe VM, VB, VL, VNA, VBA, GS150 / GS3 interested, searched [...]