When choosing crankshaft bearings, you should always pay attention to high quality. We have put together BGM ORIGINAL bearing sets for you. In addition to quality bearings, the kit also contains high-quality shaft seals. Each part of the bearing set is at least at the original manufacturer level. Shaft seals in this set are supplied exclusively by Corteco, ball bearings from renowned European [...]

bgm - Item number: BGM9030 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Motor> Motor housing> Screw sets Other customers who are interested in oil drain plug set M8 x 8mm - BGM PRO with magnet- Vespa PX, T5 125cc, Cosa, Rally180 (VSD1T), Rally200 (VSE1T), Sprint150 (VLB1T), TS125 (VNL3T), GT125 (VNL2T), [...]

The BGM Superstrong for Lambretta already has a "built-in" clutch compressor system. The Superstrong coupling can be easily compressed with just two screws and long nuts. On the face of the coupling spider, two of the legs are marked with a point, at the bottom of which is the threaded hole for the screw. Here the screws are used for pre-tensioning [...]

bgm PRO clutch springs are made in Germany and are subject to continuous quality testing. The Oteva70® material used makes the springs block-stable and true to size. The spring does not deflect sideways until it is blocked; when relieved, it returns to its original length. The clutch spring retains its full spring force. The spring rate is significantly tighter than that of a [...]

bgm - Item number: BGM7983 Availability: out of stock (Please check availability here in the Scooter Center Shop) Weight: approx. 1,80 kg Category: Frames> Wheels> Rims Other customers who are interested in rims -BGM PRO, tubeless, 2.10 -10 inch aluminum- Lambretta LI series 1-3, LI S, SX, TV series 2-3 - silver are interested, also looked [...]

Very high quality cast cylinder kit made from a special gray cast alloy. Here you will find an inexpensive cylinder kit in the very best original equipment manufacturer quality. The cylinder corresponds in all details to the original part and is therefore a very good choice if a surprising upgrade has to be made to 50 cc or the original cylinder has stretched the wings. Processing and quality of cylinder and [...]

The BGM Pro claw is made of high quality 15CrMo5 (SCM415) chrome molybdenum steel and is therefore very robust. The flanks are very tightly tolerated compared to the switching claws otherwise available on the market. This guides the claw exactly in the main shaft and effectively prevents setting / tipping. The profile for locking the gear steps has been greatly improved and [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Special tools - Made in Germany Assemble a bearing quickly and easily like a professional. That is possible with this quality tool. The bearing is neatly guided and cannot tilt. The material is spared. Used to mount the needle roller bearing of the front brake drum of the Vespa PX, T5, Cosa and PK models. Has a paragraph [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

Perfect for building your own wiring harness. bgm - Item number: BGM4751 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,20 kg Category: Workshop requirements> Electronics Other customers who are interested in Bougie pipe -UNIVERSAL Ø = 10mm- 5m - black , also searched for: Bougierohr | Heat shrink tubing | Insulating tube | [...]

High quality electric cable with robust PVC sheath. Available in many different colors, such as those used in Piaggio vehicles. Available in cable cross-sections of 0,85mm² and 2,0mm². Outside diameter 0,85mm² = Ø2,3mm outside diameter 2,0mm² = Ø3,1mm Cable type: Single core Insulation: Special PVC according to DIN ISO 6722 and LV112 Temperature range: -40 to + 120 ° C Conductor: Bare copper wire Length: 10 meters [... ]