bgm - Item number: BGM0292HS10 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,05 kg Category: Engine> Seals> Spacer Other customers who are interested in Spacer cylinder head -BGM ORIGINAL Ø52.5mm- Vespa PX125, Cosa125, GT125, GTR125, TS125, Super125 - 1.0mm are interested, also looked for: Spacer | Cylinder head | Distance seal [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Crankshaft dismantling and insertion tool set Vespa Largeframe -BGM PRO- Made in Germany Press the crankshaft out of its bearing seat quickly and easily like a professional and pull it back in again. This is possible with the quality tool from BGM PRO. With this set, the crankshaft can be pushed out of its press fit in the bearing of the engine housing in a professional and material-friendly manner and also [...]

bgm - Item number: BGM0903EX Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Engine> Exhaust> Springs Other customers who are interested in exhaust springs -BGM ORIGINAL- stainless steel (10 pieces ) - 70mm, also searched for: exhaust spring | Spring | Exhaust bracket | Exhaust retaining spring | Manifold spring | Retainer [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

Intake manifold BGM PRO for Dellorto PHBL24 / 25, Polini CP23 / 24 carburettor Suitable for Vespa GS150 (VS2 to VS5), GS2 (VD1TS), GS3 (VD2TS) Passage: Ø24mm Connection width: Ø30mm Fastening: 3-hole rubber connection steel, painted black With With this intake manifold carburetors of 24-25mm can be driven and thus the performance of the engine can be increased significantly. The carburetor is backwards in the direction of travel [...]

High-precision BGM PRO auxiliary shaft axis for the bearing of the primary drive of the Vespa PX125-200 models. Made from extremely resilient and tempered 42CroMo4V steel. Qualitatively not comparable with cheaper replicas. This means that the primary drive can be repaired with 100% factory specifications. Mandatory equipment for tuned engines. INFO: The auxiliary shaft axle has a bearing surface on which the needles of the alternator-side [...]

bgm - Item number: 4350032 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,15 kg Category: Frames> Trains> Cable pulls Other customers who are interested in train universal -Ø = 1,2mm x 2500mm, sleeve = 2200mm, nipple Ø = 3,0mm x 3mm - used as throttle cable - braided PE - gray are of interest, also looked for: [...]

bgm - Item number: 1231096 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,06 kg Category: Engine> Ignition> Vehicle electrics Other customers who are interested in exciter coil -BGM PRO- Vespa PX, PK XL, Cosa, Lambretta - including copper plates are interested, also looked for: ignition | Ignition coil | Coil | Feed coil [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

BGM PRO Oversize screw / clamp nipple in excellent quality, manufactured by a supplier for the Japanese motorcycle industry. The BGM PRO Oversize types have five special features: Production to oversize (Ø10.06mm) Stepped collar at the upper end With a wrench surface to hold against (SW = 9mm) With 3.5mm hexagon socket (like original Innocenti) With internal clamping plate to protect the train OVERSIZE The [...]

For Quattrini M210 reworked manifold for the bm PRO Big Box. This means that all Big Boxes of versions 2 to 4 can be installed on the Quattrini M210. The M210 has an angled exhaust flange on the cylinder. The angle can only be found on the M210. The TS1 outlet connection must also be reworked and adapted. The distance [...]