The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

The BGM PRO 177 piston rings are extremely break-proof, have very little friction due to their coating and are very torsion-resistant. With a thickness of 1mm, they are also suitable for very wide and high outlet shapes. The rings are packed in pairs. The piston rings with 63,0mm diameter also fit: 177 / 187ccm Parmakit 177 / 187ccm Polini Alu 177 / 187ccm Pinasco [...]

bgm - Item number: 3330039 Availability: out of stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,03 kg Category: Engine> Cylinder> Spacer Other customers who are interested in Spacer cylinder base -BGM PRO 166/172 / 177 cc- Vespa PX80, PX125, PX150 - 4.0mm (without cut-outs for overcurrent channels), also looked for: Spacer | [...]

bgm - Item number: BGM4505 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,30 kg Category: Frames> Brakes> Brake-clutch levers Other customers who wanted brake lever set -BGM PRO CNC Sport, long (165mm) - Vespa GT, GTL, GTS 125-300 - chrome are interested, also looked for: brake levers | Brake handle | Lever [...]

BGM abutments are manufactured in excellent quality by a supplier for the Japanese motorcycle industry. The dimensions correspond exactly to the old originals from Innocenti. This guarantees a perfect fit. The abutments are required to give the outer cable casing a stop on the frame or in the engine block. They are simply inserted into the corresponding hole. Uses [...]

Latest version of the proven BGM PRO HP (High Power) ignition base plate for electronic ignition. BGM has revised the well-proven BGM PRO ignition base plate and made it even better. A significantly higher light output than with conventional base plates is complemented by the very high quality of the coils and pick-up. In addition, the cabling was converted to textile-coated silicone cables. Another one [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Complete set to match your indicators and the taillight perfectly to the look of the scooter. With a few, easy-to-use hand movements, you get a great look! bgm - Item number: K070180 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,16 kg Category: Frames> Electronics> Indicator glasses [...]

Inexpensive and high-quality solution from BGM to renovate an old ignition base plate. Pre-assembled cable whips are supplied to re-solder them to an existing alternator instead of the old defective cable. The cables have professionally crimped cable plugs with shrink tubing insulation as well as stripped and pre-tinned ends for attachment to the base plate. The right bougier tube for cable protection [...]

bgm - Item number: BGM7913S Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Motor> Gearbox> Screws Other customers who are interested in screw -M10 x 160mm- steel 8,8, 7913 galvanized - used for BGMXNUMX interested, also looked for:

If a crankshaft with a longer stroke is used, this additional stroke has to be compensated for for two reasons. On the one hand due to the mechanical conditions to prevent the piston from hitting or the engine runs too highly compressed, on the other hand to keep the control angle of the cylinder, which determines the performance, within a reasonable range. If the stroke is extended, [...]

Adjustment screw set, suitable for the PHBN carburetor series from Dell'Orto (all from 10mm-17,5mm cross-section). Contains both the propeller and the idle screw. Incl. the springs and O-rings / seals behind it. For carburetors with manual choke control. The PHBN series is mainly used on vehicles with a Minarelli engine bgm - item number: 7673421 Availability: in stock (Please check availability here [...]