bgm PRO clutch springs are made in Germany and are subject to continuous quality testing. The Oteva70® material used makes the springs block-stable and true to size. The spring does not deflect sideways until it is blocked; when relieved, it returns to its original length. The clutch spring retains its full spring force. The spring rate is significantly tighter than that of a [...]

Bigbore exhaust manifold for the banana exhaust from SITO, FACO or Piaggio for Vespa Primavera and ET3 models. PERFORMANCE The exhaust manifold from BGM PRO offers more passage with a diameter of 30mm. The engine can breathe more freely and generates more torque / power. 30 mm elbow for the smallframe Sito / Faco & Piaggio 125ccm banana inner diameter 30 mm material: [...]

If the mirror holes in the handlebar trim of the GTS models from 2016 are to be closed, this is difficult to implement due to the uneven trim in this area. The specially manufactured cover caps from BGM PRO are an optical and technically first-class solution. These are made of the same material as the handlebar cover and exactly follow the design.

bgm - Item number: BGM66060P4 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Workshop requirements> Electronics Other customers who are interested in connector set for cable harness -BGM PRO- Type series 060 AM SpecialSeal, 0.85-1.25mm², waterproof - 4 plug contacts are of interest, also looked for: Plug | Cable | Ignition stator | [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

With the CDI holder from bgm it is possible to install a CDI for the electronic ignition on a Ciao of the first and second series without further modifications. The holder is simply placed under the two motor screws and attached to the motor. The following materials are required for assembly: 1. 4x washers M5x15x1,2mm 2. 2x self-locking nuts [...]

BGM gear shoulder rings are manufactured with high precision. They are hardened and ground plane-parallel to the hundredth of a millimeter. They therefore correspond exactly to the specified dimensions. The quality assurance guarantees a maximum deviation of only four hundredths of a millimeter undersize. This makes the BGM discs much more precise than Piaggio shoulder rings. WHY shoulder rings are used to compensate for the axial play between [...]

The BGM PRO variator dethrottles the drive and enables significantly better acceleration and a higher top speed. The roller tracks have been specifically calculated for each model. The sliding surface of the belt has been optimized for better grip. Thanks to the very good sliding properties of the rollers (including a sliding varnish-coated riser disc), this variator - completely gentle on the engine - already brings up [...]

bgm - Item number: BGM6413SC Availability: out of stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,18 kg Category: Frames> Trains> Speedometer cables Other customers who are interested in speedometer cables -BGM ORIGINAL- Vespa PX Lusso (from 1984), PX My, PX Disc, PX 2011, T5ccm, Cosa 125, Cosa 200, PK50 S [...]

Combined throttle / shift cable reel from BGM. It can be used as a large throttle pulley with quick throttle function. Conventional shift pulley. The larger diameter allows the existing carburetor to be opened more quickly and, above all, completely. Even carburetors with a cross-section of 30mm can be used comfortably in everyday life without having to use a noticeable external quick throttle. By [...]

BGM clamping plate sets as well as their individual parts are manufactured by a supplier for the Japanese motorcycle industry in excellent quality. The dimensions correspond exactly to the old originals from Piaggio. This guarantees a perfect fit. The high material quality enables reliable clamping of the brake cable. Also available as practical workshop sets (10 pieces) bgm - item number: BGM6482BX Availability: in stock [...]