Plastic storage dummy. This allows the crankshaft to be mounted and moved in the engine housing on a trial basis and without any effort. Thus, for pure measurement purposes, neither the crankshaft nor new bearings are stressed. Ideal to control the control angle of the crankshaft (rotary valve inlet) or the cylinder (exhaust angle, overcurrent angle). Made in Germany (US) bgm - Item number: BGM1203TL Availability: in stock (Please check the [...]

Super practical helper if the clutch needs to be changed when the vehicle is stationary. bgm - Item number: 8099015 Availability: not in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,17 kg Category: Motor> Tools> Tools Other customers who are interested in clutch centering aid -LAMBRETTA- LI, LIS, SX, TV (series 2-3) are interested, searched [...]

The BGM Superstrong for Lambretta already has a "built-in" clutch compressor system. The Superstrong coupling can be easily compressed with just two screws and long nuts. On the face of the coupling spider, two of the legs are marked with a point, at the bottom of which is the threaded hole for the screw. Here the screws are used for pre-tensioning [...]

BGM Pro gear parts are ultra-solid material. The gear wheels are made of high-alloy NiCrMo case-hardened steel (20NiCrMo2-2 / AISI8620) for the highest demands. The very good base material withstands even the highest engine performance. The precisely defined surface hardening to 58-60HRC makes the pinion extremely resistant to wear. Better than Piaggio Ware. Always consistently high quality. No compromise. BETTER Usable for all [...]

Reinforced locking ring from BGM Pro with increased material thickness and greater pre-tensioning force. This has holes so that it can be easily used with circlip pliers. The BGM Pro retaining rings are an ideal addition to all clutch baskets, especially if they are equipped with strong springs. All BGM Superstrong couplings from 2017 contain this ring type in series. bgm [...]

The BGM PRO ignition set made of high-quality components for a quick conversion of the Vespa to a maintenance-free, powerful and reliable ignition / generator unit. FEATURES Conversion from contact ignition to electronic ignition bright light already in idle voltage-stabilized 12 volt on-board network maintenance-free and reliable electronic ignition starts immediately good concentricity lighter, balanced pole wheel more power better acceleration alternator [...]

bgm - Item number: BGM6887S35 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,09 kg Category: Engine> Rubber parts> Carburettor connecting rubbers Other customers who are interested in connecting rubber with flange inlet system -BGM ORIGINAL Smart Flow- AW = Ø35mm, hole stitch = 60mm - PHBH28 / 30, VHST24-26, VHSH30, TMX27-30, TM28, PWK28, Polini24-30 are interested, also looked for: [...]

Cylinder base gasket -BGM PRO- 1,5mm Malossi 139ccm & 166ccm bgm - item number: 3820038 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,01 kg Category: Engine> Cylinder> Spacer Other customers, who are interested in spacer cylinder base -BGM ORIGINAL Malossi 139/166 ccm- Vespa PX80, PX125, PX150 - 1.5mm, were looking for [...]

Our three-pole electronic flasher relay is ideal as a replacement for a conventional flasher relay. Most manufacturers use an inexpensive mechanical relay ex works, this clocking always only depends on the attached load, i.e. on the wattage of the indicator bulbs used. If this is changed significantly, e.g. through the use of LED technology, a [...]

If the mirror holes in the handlebar trim of the GTS models from 2016 are to be closed, this is difficult to implement due to the uneven trim in this area. The specially manufactured cover caps from BGM PRO are an optical and technically first-class solution. These are made of the same material as the handlebar cover and exactly follow the design.

Revised version of the proven Lambretta bgm PRO train set. The well-known features such as the correct length of the outer and inner sleeves, the outer cable with a PE sleeve for easy operation and the detailed plan for laying the cables have of course been retained. The many small improvements in detail are new, the end sleeves are now double pressed, the inner cables are [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]