bgm - Item number: BGM6488 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,02 kg Category: Frame> Wheels> Clamping nipples and screw nipples Other customers who are interested in clamping plate set front brake -BGM ORIGINAL Vespa all models (-1981), PX (-1984) are interested, also looked for: clamping plates | Set | Rear brake cable | [...]

BGM PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® * WHY FKM / VITON® The material FKM (fluorocarbon rubber) is extremely heat, friction and fuel / ethanol resistant. Current premium fuel in Germany already contains up to 5% ethanol admixture per se. In other countries the ethanol / alcohol content is even higher. Conventional shaft seals can swell or soften when they come into contact with fuels containing ethanol. [...]

BGM Pro shims for the clutch are manufactured with high precision. They are hardened and ground plane-parallel to the hundredth of a millimeter. They therefore correspond exactly to the specified dimensions. WHY The shim is needed to distance the clutch in the engine. It is installed under the coupling pinion and is available in thicknesses of 0,8-1,6 mm (in 0,2 mm increments). [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

abc W 01 2,46 0,60 24,00 W 03 2,48 1,40 20,00 W 04 2,48 1,40 18,00 W 05 2,46 1,40 18,00 W 06 2,50 1,00 24,00 W 07 2,50 1,40 18,00 W 08 2,50 1,40 16,00 W 09 2,50 1,40 20,00 W 10 2,50 1,80 16,00 W 11 2,50 1,80 18,00 W 12 [...]

BGM PRO wire rope hoists correspond to the factory specification and impress with their high quality and low price. All trains have vehicle-specific lengths and can therefore be installed directly without rework. Particular attention was paid to high-quality details such as double-pressed end sleeves, burr-free nipples or tinned wire ends. Installation is quick and easy. To the [...]

Our BGM Pro nozzle and needle sets make the work of adjusting the carburetor much easier. The nozzle sizes extend over a wide range. This means that the right nozzle should always be with you. The practical boxes are a pleasant side effect, so the nozzles are always in the right place and the hours of rummaging through mountains of nozzles are finally over [...]

Indicator update for Vespa GTS models built before 2014! THE DESIRE The Vespa GTS models from 2014 already have an LED daytime running light which is integrated in the indicators. These indicators also fit in all previous years of the GT / GTS / GTL series. THE PROBLEM The wiring is not, however, due to the different plug types used at the factory.

Precisely manufactured nozzle suitable for all original and BGM PX200 cylinders. Other replica nozzles as well as partly new original Piaggio nozzles often have questionable undersize on the thread. The BGM PRO nozzle, however, fits 100%. Also ideal to replace an old worn nozzle. Is simply screwed into the cylinder (normal right-hand thread). bgm - item number: [...]

For permanent fixation, stickers need a clean, smooth and degreased surface. Our brake cleaner, for example, is very suitable for degreasing. In the case of larger areas to be glued, it is always an advantage to spray the area with a little water before gluing. The water can also be mixed with a few drops of detergent to make it [...]

bgm - Item number: BGM2710 Availability: out of stock (Please check availability here in the Scooter Center Shop) Weight: approx. 3,93 kg Category: Frame> Seat> Seat covers Other customers who are interested in seat covers -BGM PRO- LAMBRETTA- LI , TV (Series 2) - Red Beige are also interested in: Seat cover | Coating | Seat cover | Seat cover [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]