bgm PRO brake shoes with lining material 'MADE IN GERMANY' QUALITY The bgm Pro brake shoes are manufactured exclusively for bgm by one of the most renowned Italian brake lining manufacturers. The covering material comes from the German manufacturer Beral. Like the original, the brake disk is made of aluminum. MATERIAL + PERFORMANCE The pad mixture for the bgm PRO brake pad has a high coefficient of friction averaging [...]

Conversion wiring harness for retrofitting to: Vespatronic ignition system in Rally, Sprint, VBB, Super, VNA, VNB, etc. The retrofitting to a more modern alternator / ignition type is a tried and tested means to be more durable and safe on the road. The non-contact CDI ignitions are almost indestructible and reliable, and the light output with a modern, regulator-supported on-board electrical system is around

TIP: Please always assemble piston rings carefully. Piston rings made of cast material are only elastic to a limited extent and break relatively quickly. Some pistons have trapezoidally profiled piston rings (so-called keystone rings), these only fit in one installation position. If the ring does not move freely, please loosen it carefully and put it back in 'upside down'. Very helpful tools for work [...]

BRAKE CALIPER MOUNT 'TOURING RADIAL' BGM PRO FOR Vespa PX Professional brake caliper mount from BGM PRO 'Made in Italy'. Enables the assembly of the radially attached BGM PRO 4-piston brake caliper. With fine controllability, this enables braking values ​​at motorcycle level. MAXIMUM DECELERATION A special feature of the BGM PRO brake calliper adapter is its uncompromising design for the greatest possible deceleration. The brake caliper was [...]

bgm - Item number: 7900056 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,00 kg Category: Engine> Carburettor> Carburettor components Other customers who are interested in mixture adjustment screw -BGM PRO for PWK- (bgm, Stage 6, Keihin), PWM38, also looked for: mixture adjustment screw | Adjusting screw | Carburetor screw | Propeller | Co2 [...]

The bgm PRO silent rubbers improve the driving behavior through a much more precise guidance of the motor in the frame. The reinforced rubbers only have a slightly increased degree of hardness. Therefore, the driving comfort is maintained despite the tighter suspension. With the reinforced bgm motorsilent rubbers, the chassis gains directional stability, steering precision and rigidity. The assembly is simple and offers eg [...]

The bgm PRO Racing shaft with 54 mm stroke is the maximum for racing or ambitious road tuning. In contrast to a normal shaft, the cheek diameter has been increased in order to achieve the necessary, higher overlap on the crank pin and thus additional security against rotation despite the increased stroke. This minimizes the risk of twisted cheeks and welding with [...]

Motor housing bolt set that contains all removable motor bolts of the motor housing. The bolts are made of high-strength steel (10.9) and are permanently protected against corrosion by a browning process. Also included are the snap rings, washers and nuts, all of which are galvanized. The set corresponds to the original dimensions used ex works and is a high-quality 1: 1 replacement for the original [...]

The centrifugal weights in the variator are wearing parts and must be changed at regular intervals depending on the load (wear check approx. Every 5000 km). Wear of the rollers is characterized by a flattening on one side, the rollers can then no longer slide properly in the runway of the variator. This results in poor acceleration and often also a lower [...]

Cable branch for connecting the battery / starter relay to the starter motor. This cable branch is not part of the rest of the cable harness and is no longer manufactured by Piaggio. Exactly reproduced in high quality according to the original. Essential part for the perfect restoration. The Elestart works like it did on the first day. bgm - Item number: SC5020 Availability: in stock (Please [...]

BGM screw / clamp nipples are manufactured by a supplier for the Japanese motorcycle industry in excellent quality. The dimensions correspond exactly to the old originals from Piaggio / Innocenti. This guarantees a perfect fit. As in the original, the clamping screws for the shift cables have an internal plate. This protects the inner cable of the Bowden cable and helps to [...]

bgm - Item number: BGM6399UB Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,29 kg Category: Frames> Cables> Cables Other customers who are interested in universal train -BGM ORIGINAL, Ø = 1.9 mm x 2500mm, sleeve = 2200mm, nipple Ø = 8.0mm x 8mm, inner sleeve PE, black - used as a clutch cable, front brake cable are interested in looking [...]